How do you clear the AF code on a dryer

To clear the code, press STOP once and the estimated time remaining countdown should return to the display. The AF code will continue to appear with each cycle until the low airflow condition is resolved.

Why does my dryer keep saying AF?

The letters “AF” flashes if a restricted air flow condition exists, meaning that 3 consecutive cycles were run with airflow less that 19CFM. Check the entire venting system for any kinks or restrictions. Check the door seal and drum seals.

What is AF code?

Country Code AF Country code according to ISO-3166 Alpha-2 AF is the two-letter country abbreviation for Afghanistan.

What does sensing mean on a Maytag dryer?

Sensing – The Sensing indicator will light during Sensor Cycles to indicate that the moisture sensor on the dryer is operating. This indicator will not light during Timed Cycles or options such as Wrinkle Prevent. Wet – The load is still wet and/or the cycle just started.

What does the code AF mean on a Kenmore dryer?

The code AF normally indicates that the control senses a restricted air flow on most models of Kenmore Elite dryers.

What does F01 mean on a Whirlpool Duet dryer?

If your Whirlpool dryer is displaying an F01 error code, this means there is something wrong with the control board or one of the components connected to it. It is commonly caused by a power failure or after a power surge occurs.

What does RF mean on a Whirlpool dryer?

ANSWER Hello Lenore. The error code you provided is for a restricted vent in the unit. Check and make sure the lint filter is clean, and the dryer vent is clear and not clogged or kinked.

How do I clean the lint out of my Maytag dryer?

1. Roll lint off the screen with your fingers.
2. Wet both sides of the lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup.
4. Rinse screen with hot water.
5. Thoroughly dry the lint screen with a clean towel.

Why does my dryer always say check vent?

If the Check Vent indicator is lit, it means the airflow is limited going through the dryer and to the outside. This can be due to the lint screen or vent is clogged; the vent is crushed or kinked or has too many turns. Check to see if the vent run from the dryer to the wall is crushed or kinked.

What does AF mean on my Bravos XL dryer?

An AF (Restricted Air Flow) or “Check Vent” error code indicates that the lint screen or vent is clogged; the vent is crushed, kinked or has too many turns. The dryer will continue to run when the is error is present.

Article first time published on

How do you turn off the sensor on a Maytag dryer?

To change the drying settings: The dryer must be in standby mode (power is off) to adjust the default settings. Before starting a cycle, touch and hold DRYNESS for 6 seconds. Touch DRYNESS to select the dryness level shown in the time display: 0, 1, 2, 3, or 4. Touch START/PAUSE to save the new dryness level setting.

How do you know if your dryer sensor is bad?

If the dry clothing test works, you then will want to place damp clothing inside your dryer. When the clothing is damp, your dryer should run until the clothing is dry. If your dryer runs for more than just a few minutes and doesn’t shut off, that means it has passed the test as well.

Why does my dryer get hot but not dry clothes?

There are several reasons why the dryer is heating up, but still not drying clothes and it might take several hours to finally get them dry. The reasons are: clogged exhaust vent, faulty heating element, malfunctioned cycling thermostat or clogged lint trap.

Where is country code AF?

CountryAlpha-2 codeAlpha-3 codeAfghanistanAFAFGAlbaniaALALBAlgeriaDZDZAAmerican SamoaASASM

How do you fix the dryer?

1. Clean the lint screen.
2. Check to see if the house vent from the dryer to the wall is crushed or kinked.
3. Confirm that the house vent from the dryer to the wall is free of lint and debris.
4. Confirm that the exterior vent exhaust hood is free of lint and debris.

What does AF mean on a Maytag washer?

An AF (Restricted Air Flow) error code indicates that the lint screen or vent is clogged; the vent may be crushed, kinked or have too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.

What does F mean on Whirlpool dryer?

The F-01 error code indicates a primary control failure. The primary controls are located inside the main control panel where the dryer cycles and settings are displayed.

How do I fix code F01?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.

How do I fix F01 error?

The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse.

What does sensing mean on my dryer?

There are sensor strips in the drum of the Duet dryers. As your load of laundry tumbles in the drum, it makes contact with the sensor strips so that the dryer can end the cycle when the laundry is dry. The drying cycle can end early if the dryer is not level.

How do you turn off the sensor on a Whirlpool dryer?

Remove the lint screen housing from the dryer, and place it on a flat surface. Using a pair of needle nose pliers, push on the sensor bar tab that locks the sensor into the lint screen housing. Then, turn the housing over and pull the sensor off the lint screen housing.

How do I check the airflow on my dryer?

Check the vent for proper air flow by placing your hand over the exterior vent while the dryer is running. You should feel a strong flow of air.

How do I clean the lint out of my front load dryer?

1. Remove lint screen from the dryer and wash in warm soapy water (see notes below)
2. Use a screwdriver to remove the “cover” from the lint filter compartment and thoroughly clean with vacuum and microfiber cloth.
3. Use a lint vent cleaning brush to loosen lint and debris inside the dryer.

How do I know if my dryer vent is clogged?

1. Clothes take longer than the normal 35-40 minutes to dry.
2. dryer vent hood flap does not open properly.
3. debris appears around the outdoors dryer vent opening.
4. you feel excessive heat in the room where the dryer is running.
5. lint and debris accumulate around the dryer’s lint filter.

How do you install a side vent on a Maytag dryer?

1. Decide on the route of the side vent. …
2. Mark on the outside of the house where the exhaust vent will go, and cut a hole in the wall with a jigsaw. …
3. Connect the exhaust vent to the hood with a 4-inch clamp. …
4. Connect the vent to the exhaust outlet in the dryer.

What does a dryer sensor look like?

Typically, the moisture sensor in your dryer consists of two metal bars mounted on a black plate. The two metal bars will protrude into the dryer’s drum. … As the moisture dissipates, the current becomes weaker. When the sensors can no longer detect moisture in the clothes in the drum, the dryer automatically turns off.

Why is my Maytag dryer not getting hot?

If your Maytag dryer is not heating, it is possible that it is not being supplied with the proper voltage. Most electric dryers require two legs of 120 volts AC that is equal 240 volts. If one leg of voltage is shut off by a tripped breaker or blown fuse, the dryer may be able to run but it will not heat.

Where is the moisture sensor on my Maytag dryer?

It’s typically found on the back wall of the dryer drum or in the front near the lint trap. Use fine grit sandpaper to scrub the moisture sensor. This will help remove fabric softener build-up, lint, or any debris that is interfering with the sensor.