What is an electrical stub

In microwave and radio-frequency

When should you use a stub?

Stub out elbows are primarily used when installing PEX pipe to stub out of the wall and allow for further connection of outlet stop valves and plumbing fixtures. Stub out elbows with ears can be nailed to a wooden surface, such as a stud.

What is the purpose of a stub out?

A stub-out is the exposed portion of a pipe installed during a plumbing, electrical or gas rough-in that is ready for connection to a fixture or device.

What is the function of stub cable?

Stub Cable- Stub Cable is factory process filled cable that is cut to customer specified lengths eliminating time-consuming cable preparation at the customer job site.

What is stub implementation?

A stub, in this context, means a mock implementation. That is, a simple, fake implementation that conforms to the interface and is to be used for testing.

What is a stub up in construction?

Home / Glossary / Stub-up. A term used to indicate that preparation has been made to install a fixture. An example is that a drain pipe is stubbed up in the floor in preparation for attaching a toilet.

What is a stub out plumbing?

The plumbing stub-outs are the end result of the rough-in phase of plumbing a residential or commercial building. They are usually installed while the walls are still uncovered; and after the drywall work and painting is complete, a plumber comes back and hooks them up to the plumbing fixtures.

What is a stub tuner?

Stub tuners are impedance transformers that are designed to introduce a variable shunt susceptance into a coaxial transmission line. They consist of one or more short-circuited, variable length lines (stubs) connected at right angles to the primary transmission line.

What is stub in RF?

In microwave and radio-frequency engineering, a stub or resonant stub is a length of transmission line or waveguide that is connected at one end only. … Stubs are commonly used in antenna impedance matching circuits, frequency selective filters, and resonant circuits for UHF electronic oscillators and RF amplifiers.

Why is stub matching needed?

In a strip line circuit, a stub may be placed just before an output connector to compensate for small mismatches due to the device’s output load or the connector itself. Stubs can be used to match a load impedance to the transmission line characteristic impedance.

Article first time published on

How long should a stub out be?

Wall Drains Like the supply stub-outs, the drain stub-out extends from a fitting — usually a sanitary tee — to a point 3 or 4 inches beyond the wall. The drain, which is usually 2-inch plastic pipe, maintains a minimum slope of 1/4 inch per foot from the stub-out to the point where it ties into a main waste pipe.

How do I remove stubs?

Cut the PVC pipe at any point inside the wall that allows you to remove the stub-out, using a hacksaw. You may have to make two cuts to separate the tee holding the stub-out from the waste and vent pipes. Remove any clamps holding the stub-out with a screwdriver or hammer, and pull out the stub-out.

What is a stub soil stack?

A stub stack is a cut-off version of an SVP, which is fitted with an air admittance valve to prevent foul smells. The stub stack should still be a 100mm diameter pipe. Rules on the use of stub stacks are commonly forgotten.

What is the difference between mock and stub?

A Mock is just testing behaviour, making sure certain methods are called. A Stub is a testable version (per se) of a particular object.

What is the difference between stubs and drivers?

Stubs are basically known as a “called programs” and are used in the Top-down integration testing. While, drivers are the “calling program” and are used in bottom-up integration testing. … Whereas the drivers are used if the main module of the software isn’t developed for testing.

What is stub in unit test?

A stub is a small piece of code that takes the place of another component during testing. The benefit of using a stub is that it returns consistent results, making the test easier to write. And you can run tests even if the other components are not working yet.

Do I need a stub out with PEX?

#38; they flop around. Even cpvc would have been a better stub out, cause you can atleast make that square & rigid. Copper stubs is my weapon of choice. Pex is fine to get from point “A” to point “B”, but damn, make sure your plumber stubs out in something that looks decent & is square to the wall.

How far should a stub out extend through a finished wall?

The drain stub-out extends from a fitting — usually a sanitary tee — to a point 3 or 4 inches beyond the wall. If you are referring to the rough plumbing, it should be flush with the finished wall. If it has to stick out of the wall, no more 1 inch, or enough pipe to receive the the next fitting.

What is meant by stub matching?

[′stəb ‚mach·iŋ] (electromagnetism) Use of a stub to match a transmission line to an antenna or load; matching depends on the spacing between the two wires of the stub, the position of the shorting bar, and the point at which the transmission line is connected to the stub.

What is stub in Smith chart?

Stub tuning is one method that satisfies both of these criteria; stub tuning is simply the process of adding a length of transmission line to the existing length in either series, shunt, open circuit, or short circuit configuration to match the line to the load.

Why do we use short circuit stubs instead of open circuit stubs?

Short circuited stubs are preferred to open-circuited stubs because the latter are, more difficult to make and correct. made of a transmission line with a different Z0. liable to radiation from open end.

Can we have triple stub?

Triple-Stub Matching The disconnection is not physical and is achieved by simply adjusting the length of the stub to . The -stub appears open at the junction point D. C and D for double-stub matching.

How high is a sink drain stub out?

Re: Standard height for under sink connections? The drain stub out can be 12″ from the floor to accommodate a disposer, even if you don’t plan on installing one. The H&C water could be 16″ off the floor. These measurement should work for you.

What size stub out for bathroom sink?

Pipe Size. The pipe stub-outs under your sink are branch pipes that connect to 3/4-inch main pipes, and they always have a diameter of 1/2 inch. Plumbers conform to this standard whether installing copper, chlorinated polyvinyl chloride (CPVC) or polybutylene (PB) pipes.